Description of the USB or LAN receiver set with:
- a 433.92MHz receiver with receiving modes for:

• X10, Digimax, RFXPower, RFXMeter, RFXSensor,

• Oregon Scientific, cent-a-meter Electrisave, OWL

• KlikAanKlikUit, HomeEasy, NEXA, Chacon, Proove, Domia Lite, ELRO AB600, BBSB

• ATI Remote Wonder, ATI Remote Wonder Plus.

This receiver is able to receive:

• The signals Non-US X10 lighting and X10 security sensors,

• Digimax,

• HomeEasy,

• KlikAanKlikUit,

• Chacon,

• NEXA,

• Proove

• Chacon

• Domia Lite,

• ByeByeStandBy

• ELRO AB600,

• Intertechno

• Düwi

• RFXSensor devices

• RFXPower & RFXMeter devices,

• ATI Remote Wonder,

• cent-a-meter, Electrisave, OWL CM113, CM119, CM160

• Oregon Scientific sensors:
  See the document contents for the currently supported sensors.

  A lot of other Oregon Sensors can be received too but only the packet format of the listed sensors is made available in the documentation delivered with the receiver.

The USB/LAN receiver set contains a master receiver and a connector for an optional slave receiver.

The function of the master is to control the data flow on the communication interface.

For the list of supported by software click here.

Capabilities of these receivers:

·         Receive and decode X10 RF, X10 security, NEC packets up to 48 bits.

·         Receive and decode Chacon, HomeEasy, KlikAanKlikUit, NEXA, Proove,

·         Receive and decode Domia Lite, ELRO AB600, Intertechno, Düwi, ByeByeStandBy,

·         Receive and decode RFXMeter, RFXSensor and RFXPower.

·         Receive and decode ATI Remote Wonder packets.

·         Receive and decode Oregon Scientific 1.0, 2.1 and 3.0 packets.

·         Receive and decode cent-a-meter, Electrisave,OWL CM113, CM119 and CM160.

·         RFXCOM variable length mode and 32 bit mode,  (W800 compatible mode)

·         BNC antenna.

Firmware revision history:

Note: to know your receiver version, use RFreceiver and push the "Get receiver version" button.

Version 02

• production version with 16F676 processor

Version 03

• 16F688 processor added

Version 04 to 08

• Firmware improvements

Version 09

• coexistence of a Visonic receiver

• delay XRTS - XCTS changed from 32 to 96ms

Version 0A

• mode 48bits removed

Version 0B

• Oregon 1.0 and 2.1 receiving added

• only 16F688 processor supported

Version 0C and 0D

• Firmware improvements

Version 0E

• support for Oregon 3.0 added

Version 0F

• jamming detect changed from 16ms to 3.2sec

• 32 bit X10 mode removed

Version 10

• jamming detect changed from 3.2sec to 96ms

Version 11

• Oregon receiving optimized to ignore spike at packet end

Version 12

• One receiver for X10 + Oregon + KlikOn-KlikOff etc.

Version 13

• One receiver for X10 + Oregon + ATI + KlikOn-KlikOff etc.

Version 14

• Hang problem solved if X10 mode was disabled.

Version 15

• Minimum packet length for Oregon changed to 64 to support also the UVN800.

Version 16

• Support for ATI Remote Wonder Plus added.

Version 17

• Error solved: KlikOn didn't work correctly when ATI enabled.

• Receiver is a bit more sensitive for X10 and KlikOn.

• jamming detection removed.

Version 18

• ELRO AB600 wall switch receiving optimized

Version 19

• F02E not used to disable Oregon.

Version 20 = 1A

• KAKU receiving optimized, if more then 24 bits received ignore packet

• if KAKU or Koppla mode is set stop X10 only receiver

• ACK send if KAKU, Koppla or Visonic cmd received by Master receiver

• Version Request also responds if receiver not active.

Version 1B

• support for the Oregon BWR102. (European version only)

Version 1C

• THR128, packets with non decimal value in temp fields are ignored.

Version 1D

• GR101 support

Version 1E

• Support for RFXCOM Homeseer plug-in

Version 1F

• technical release

Version 21

• BWR102 US version added

• new ARC receiving added

• arc only has packet length byte

• RAW mode removed

• receiver a bit more sensitive.

Version 22

• Support for disable Visonic receiver command

Version 23

• Error corrected: no X10 if ARC and Oregon both disabled

Version 24

• Receiving of HomeEasy and KlikAan with automatic coding added

• BTHR918 and other 918 Oregon sensors received correctly

Version 25

• X10 was received even if disabled.

Version 26

• Problem with transmitter handshake solved

Version 27

• Version request waits now for RS232 buffer empty

Version 28

• Master/Slave sync problem solved

• HomeEasy heater protocol added

Version 29

• Receiving for new Electrisave model added.

Version 2A

• Receiver version 29 with CM119 support.

Version 2B

• Receiving of HomeEasy EU added.

Version 2C

• Receiver version 2B with CM119 support.

Version 2D

• Receiving of old KlikAanKlikUit AC switches added.

Version 2E

• Receiver version 2D with CM119 support.

Version 50

• Receiving of HomeEasy EU motion sensors.

Version 51

• Receiver version 50 with CM119 support.

Version 54

• Integrated receiver in RFXLAN V3. Same as version 51