Description of the USB, LAN or WLAN receiver set with:
- a 310MHz X10 receiver and
- a 433.92MHz receiver with receiving modes for:

• X10, Digimax, RFXPower, RFXMeter, RFXSensor,

• Oregon Scientific, cent-a-meter Electrisave, OWL

• KlikAanKlikUit, HomeEasy, NEXA, Proove, Domia Lite, ELRO AB600, BBSB

• ATI Remote Wonder, ATI Remote Wonder Plus.

This receiver is able to receive:

• The signals from US and Non-US X10 lighting and X10 security sensors,

• Digimax,

• HomeEasy,

• KlikAanKlikUit,

• NEXA,

• Proove

• Domia Lite,

• ByeByeStandBy

• ELRO AB600,

• RFXSensor devices

• RFXPower & RFXMeter devices,

• ATI Remote Wonder,

• cent-a-meter, Electrisave, OWL,

• Oregon Scientific sensors:
  See the document contents for the currently supported sensors.

  A lot of other Oregon Sensors can be received too but only the packet format of the listed sensors is made available in the documentation delivered with the receiver.

The USB/LAN/WLAN receiver set contains a master receiver and a connector for an optional slave receiver.

The function of the master is to control the data flow on the communication interface.

For more information see the receiver documentation at the download page.

For the list of supported by software click here.

Capabilities of these receivers:

• Receiver sensitivity of -106dBm with SAW filter input.

• Jamming detection in X10 mode.

• Receive and decode X10 RF, X10 security, NEC packets up to 48 bits.

• Receive and decode HomeEasy,

• Receive and decode KlikAanKlikUit,

• Receive and decode NEXA,

• Receive and decode Proove,

• Receive and decode Domia Lite,

• Receive and decode ELRO AB600,

• Receive and decode ByeByeStandBy,

• Receive the RFXMeter, RFXSensor and RFXPower signals.

• Receive and decode ATI Remote Wonder packets.

• Receive and decode Oregon Scientific RF packets.

• In 32 bits modes, some Oregon temperature sensor information is translated to RFXSensor format.

• Receive and decode cent-a-meter, Electrisave,OWL RF packets.

• 2 receivers on 1 interface. (1 Master and 1 Slave)

• Handshake signal to allow a RF transmitter to transmit on the same frequency.

• Software selectable decoding and output:

  32 bit direct,  (W800 compatible mode)

  variable length mode with number of bits received.

• The RS232 data format is 4800bd or 38400bd, 8 bits data, no parity, 1 stop bit.

• BNC antenna connection.

DIY extension possibilities:

There are connection possibilities for a pushbutton switch and a relay.
When the pushbutton input is low, the device address of a received X10 command is saved. A received On-Off command for this device address will switch the Relay output.

433.92MHz receiver firmware revision history:

Note: to know your receiver version, use RFreceiver and push the "Get receiver version" button.

Version 02

• production version with 16F676 processor

Version 03

• 16F688 processor added

Version 04 to 08

• Firmware improvements

Version 09

• coexistence of a Visonic receiver

• delay XRTS - XCTS changed from 32 to 96ms

Version 0A

• mode 48bits removed

Version 0B, 0C, 0D and 0E

• Firmware improvements

Version 0F

• jamming detect changed from 16ms to 3.2sec

• 32 bit X10 mode removed

Version 10

• jamming detect changed from 3.2sec to 96ms

Version 11

• Oregon receiving optimized to ignore spike at packet end

Version 12

• One receiver for X10 + Oregon + KlikOn-KlikOff etc.

Version 13

• One receiver for X10 + Oregon + ATI + KlikOn-KlikOff etc.

Version 14

• Hang problem solved if X10 mode was disabled.

Version 15

• Minimum packet length for Oregon changed to 64 to support also the UVN800.

Version 16

• Support for ATI Remote Wonder Plus added.

Version 17

• Error solved: KlikOn didn't work correctly when ATI enabled.

• Receiver is a bit more sensitive for X10 and KlikOn.

• jamming detection removed.

Version 18

• ELRO AB600 wall switch receiving optimized

Version 19

• F02E not used to disable Oregon.

Version 20 = 1A

• KAKU receiving optimized, if more then 24 bits received ignore packet

• if KAKU or Koppla mode is set stop X10 only receiver

• ACK send if KAKU, Koppla or Visonic cmd received by Master receiver

• Version Request also responds if receiver not active.

Version 1B

• support for the Oregon BWR102. (European version only)

Version 1C

• THR128, packets with non decimal value in temp fields are ignored.

Version 1D

• GR101 support

Version 1E

• Support for RFXCOM Homeseer plug-in

Version 1F

• technical release

Version 21

• BWR102 US version added

• new ARC receiving added

• arc only has packet length byte

• RAW mode removed

• receiver a bit more sensitive.

Version 22

• Support for disable Visonic receiver command

Version 23

• Error corrected: no X10 if ARC and Oregon both disabled

Version 24

• Receiving of HomeEasy and KlikAan with automatic coding added

• BTHR918 and other 918 Oregon sensors received correctly

Version 25

• X10 was received even if disabled.

Version 26

• Problem with transmitter handshake solved

Version 27

• Version request waits now for RS232 buffer empty

Version 28

• Master/Slave sync problem solved

• HomeEasy heater protocol added

Version 29

• Receiving for new Electrisave model added.

Version 2A

• Special receiver version with CM119 support.

310MHz receiver firmware revision history:

Version 02

• production version with 16F676 processor

Version 03

• 16F688 processor added

Version 04 to 08

• Firmware improvements

Version 09

• coexistence of a Visonic receiver

• delay XRTS - XCTS changed from 32 to 96ms

Version 0A

• mode 48bits removed

Version 0B to 0E

• Firmware improvements

Version 0F

• jamming detect changed from 16ms to 3.2sec

• 32 bit X10 mode removed

Version 10

• jamming detect changed from 3.2sec to 96ms

Version 11 and 12

• Firmware improvements

Version 30

• version number changed to distinguish the 310MHz receiver from the 433.92MHz receiver.
  Version 30 is equal to version 12

Version 31

• if KAKU or Koppla mode is set then stop X10 only receiver

• ACK send if KAKU, Koppla or Visonic cmd received by X10 only Master

• Version Request also responds if receiver not active.

Version 32

• Support for RFXCOM Homeseer plug-in

Version 33

• Support for disable Visonic receiver command

Version 34

• Version Request waits for RS232 buffer empty.

Version 35

• Master-Slave sync problem solved ( packet length was sometimes wrong)